Cutting composite decking requires the right tools, a suitable saw blade and careful measurements to achieve a clean, accurate finish.
Whether you’re cutting boards to length, making angled cuts or working around obstacles, this guide explains how to cut composite decking, which tools to use and how to avoid damaging the boards.
Can You Cut Composite Decking?
Yes, composite decking can be cut using standard woodworking tools, including circular saws, mitre saws, table saws and jigsaws. However, it’s important to use a suitable blade and cutting technique to achieve a clean finish without damaging the board.
The Tools Needed to Cut Composite Decking
If you are carrying out composite decking installation, the following tools will be required for cutting the composite decking boards.
- Chalk
- Tape Measure
- Speed Square
- PPE
- Mitre Saw
- Circular Saw
- Jigsaw
- Table Saw
It is unlikely you would need all four saw types. The following section discusses these options and their benefits.
What Saw and Saw Blades Best for Cutting Composite Decking?
Choosing the right saw blade is important when cutting composite decking. A suitable blade helps produce a clean edge while reducing the risk of chipping, overheating or damaging the board’s surface.
Carbide-tipped blades are commonly used for cutting composite materials because they retain their sharpness and can provide a consistent finish.
When choosing a blade, consider:
- Blade compatibility: Use a blade suitable for your saw and the composite material.
- Tooth count: Blades with more teeth generally produce a finer finish, although the ideal number depends on the blade diameter and material.
- Cutting speed: Maintain a controlled cutting speed to avoid excessive heat build-up.
- Board construction: Capped and uncapped composite boards may have different cutting requirements.
Always follow the decking manufacturer’s cutting recommendations and the saw blade manufacturer’s instructions.
Circular Saw
A Circular uses a rotary motion to spin the saw blade around an arbour. Circular saws are versatile power tools used professionally and in DIY projects.
The sharp saw blades are disc-shaped, and larger saw blades can be used for a deeper cut. The amount of teeth a circular saw blade has will affect the speed it can cut at.
Table Saw
Unlike circular saws, table saws are not mobile. The circular blade on a table saw is mounted on an arbour and will have an electric motor to drive it.
The blade comes through the table, and the composite board is then pushed into it for an accurate cut.
This differs from the circular saw that is controlled and pushed against the secured decking board.
The blade can be moved up and down to adjust the depth of the cut. You can also explore composite cutting table saw blades that are specially designed for cutting composite materials.
Miter Saw
A mitre saw, also spelt “miter saw” in some cases, is a saw that is mounted on a pivoting swing arm that allows the user to quickly and accurately cut at various angles.
Triple chip tooth mitre saw blades are available to produce a fine cut that won’t chip the delicate plastic veneer of a composite deck board.
Jigsaw
A jigsaw is a much more accurate saw type that allows the user to cut curves and shapes.
A jigsaw is a great option for cutting composite decking that needs to go around shapes such as drain pipes.
Thin, flexible jigsaw blades are easier to cut curves with, and the teeth are measured in teeth per inch (TPI). A high TPI results in finer, smoother, and more accurate cuts.
How to Cut Composite Decking Boards
Now that you know all about the cutting tools needed to cut composite decking boards, you may want to know more about the cutting process.
It is important to mention that before you start cutting different materials, you must ensure your safety is a priority.
Always work in a well-ventilated area, and make sure you wear the necessary PPE. Your personal protective equipment should include a dust mask to minimise the risk of inhaling airborne particles.
Safety goggles should always be worn when using a saw to protect your eyes from chips or broken blades that can occur. Alternatively, a face shield can be used to give you additional protection.
Hearing protection is also recommended, as saws can be extremely loud. Gloves and loose-fitting clothing should be avoided when working with power tools to minimise the risk of it getting caught.
Composite Board Preparation
Preparing your boards to be cut is essential. Cleaning the boards and storing them in dry places out of direct sunlight is important.
Composite decking can be affected by thermal expansion, so cutting them when they are cool will allow you to get a more accurate cut.
You should then ensure the outer edges of the board are square. To do this, you should measure an eighth of an inch from the edge using a speed square. A chalk line should be drawn down the board length, and this area can be cut.
Measuring
Accurately measuring the area where your decking installation will take place and taking into account the required gaps between boards and external walls is essential. Only then will you be able to measure your boards accurately.
Allowing additional length, so the board overhands the subframe, will allow you to cut and create a flush finish. It is always better to allow additional length at this point as this allows you to cut it down accurately. Cutting too short will result in a wasted deck board.
Straight Cut
Straight cuts are the most straightforward and are typical of square or rectangular decking areas.
Using chalk to mark where to cut clearly is advisable. This can then be cleaned off or removed for adjustments.
Angle Cut
Decks that feature diagonal sections or edges might seem like a daunting task, but this can be as straightforward as straight cuts with the correct planning and tools.
With the correct saw blades, using a mitre saw to cut at the required angle is simple.
Measuring the correct angles is an important part of this process and taking care to ensure your measurements are correct is vital.
Cutting Curved Boards
Curved boards can be cut in the same ways that straight and angled boards are.
The main difference is that the shape or curve of a board may require additional cuts to be made near the edges.
What Happens After Cutting Composite Decking?
Once your composite decking boards have been cut to the required dimensions, check that the edges are clean and the boards are ready for fitting.
The next stage involves positioning and securing the boards according to the manufacturer’s installation requirements.
For detailed guidance on preparing the supporting structure, fixing boards and completing the deck, see our How to Install Composite Decking guide.
FAQS
Should I Sand Composite Decking After Cutting It?
Generally, you shouldn’t sand composite decking unless the manufacturer specifically recommends it.
Sanding can alter the surface finish, particularly on capped composite boards, and may affect warranty coverage.
For cleaner cuts, use a suitable sharp saw blade and follow the manufacturer’s cutting recommendations.
Should I Seal the Ends of Composite Boards After Cutting?
Most composite decking systems don’t require the cut ends to be sealed, but requirements vary between manufacturers and board constructions.
Check the installation instructions for your chosen decking before applying any sealant, wax or other treatment.
Using an unsuitable product could affect the appearance or performance of the board.
Final Thoughts
Cutting composite decking is relatively straightforward with the right tools, a suitable saw blade and careful preparation.
Circular saws and mitre saws are useful for straight and angled cuts, while jigsaws can help when cutting around curved edges or obstacles.
The key to a good finish is accurate measuring, proper board support and controlled cutting. Always wear appropriate protective equipment and follow the manufacturer’s recommendations for your chosen decking.
Taking your time with each cut can help reduce wasted materials and achieve clean, professional-looking edges.




